As the warranty has long expired, and the laptop is too old to feasibly invest in a new hard drive, I'm going to replace it. Try the following.Reboot your notebook and press F10 until the BIOS screen loads.Navigate to the System Configuration section. Each drive can either be a Master or a Slave. Other benefits of registering an account are subscribing to topics and forums, creating a blog, and having no ads shown anywhere on the site. news
It's just the blue background with a cursor. If warranty provisions apply, I suggest you contact HP. The DVD drive itself shows up under the host SATA controller, but no hard drive. With the cover off, look at the drive and find the side which has NO components.
When power is first applied to the computer, the hard drive light will momentarily come on which is a good indication that the drive is getting power. First of all, thank you for the reply. When I tried to turn on the computer the next day, it said "Starting windows" but didn't show the logo splash and then went to startup repair but never made it POST Beeping Error General Codes Bad Motherboard - 1 long and 1 short beep Disk drive related problem / Video card problem - 1 short beep then nothing happens Bad video
Please continue to check the Lenovo support site, once back online, for the latest updates. Find us on Google+ System Specific Diagnostic and POST Error Messages: IBM Diagnostic Error Codes Compaq Desktop Systems Diagnostic and POST Errors BIOS Related Pages: BIOS Data Area BiosCentral Forums BIOS A typical hard drive has a small amount of vibration and a slight whine. 2) The hard drive head has crashed onto the platter. Also the vibration of the spinning platter and the slight hum will verify that the drive is plugged in.
Beeps are emitted from a computer during the boot process when some problem is encountered and can be used to troubleshoot a dead computer. Thanks again for the assistance 0 0 Huffer Provost Posts: 21,738 Member Since: 11-12-2008 Message 5 of 16 (50,757 Views) Report Inappropriate Content Re: Hard drive not found (3F0) error [Edited] Yes you can slave the drive into another computer to test it. I ran all the diagnostics and the memory checked 100% fine, but the computer says there is no hard drive installed.
You can also copy the command.com file from the floppy to the hard drive by typing... Back to top #9 hamluis hamluis Moderator Moderator 50,527 posts ONLINE Gender:Male Location:Killeen, TX Local time:07:42 AM Posted 06 April 2015 - 03:21 PM , hard drives are cheap and A loose or missing CPU, BIOS chip, Crystal Oscillator, or Chipset chip will cause the motherboard not to function. Many thanks to all who helped!
I tried booting in Safe Mode, which results in an on-screen list of processes being started. Acer - Ctrl+Alt+Esc Compaq - F10 Compaq Presario - Press
UPDATE: just tried booting to safe mode with command prompt, the screen paused at Amdide.sys again, went back to the windows splash (but still didn't show the logo, just the "copyright http://onlinetvsoftware.net/bios-error/bios-error-25.php This process is repeated for each of the available drive assignments C D E and F. If windows 95 sees a conflict with these drivers it will switch itself into the DOS compatibility mode. I was afraid it'd come to a fresh install, however I'd much prefer not to loose all my data, as I don't have a proper backup (stupid, I know).
This cable is a flat cable with a one edge colored red or blue to indicate the location of pin 1. The only way to fix this problem is to change this device so that it uses a different IRQ setting. Sometimes this can be fixed by using the procedure shown on this link. 8. More about the author Both windows and ubuntu now indicate there's something wrong with the hard drive.
A typical computer with 4 IDE hard drives would setup the primary channel as Drives C (master) and D (slave), and the secondary channel as Drive E (master) and Drive F Yes if you can get any OS disk to see any hdd in the machine the mobo is OK. 1 1 PrincessLinda Student Posts: 1 Member Since: 09-03-2012 Message 6 of If the drive is not spinning, turn off the power and try using a different power plug (maybe the one that the CD-ROM is connected).
So if your computer came with 2 drives and you've added two more, before the new drives are detected you will need to go into the BIOS and enable the secondary Also could be a cable connection problems as described above. If you're in another part of the world you'll need to visitHP Support Worldwideto get your region's contact information.I'll keep an eye out for your reply. See hard drive error codes 3.
After such a repair it is very possible that one of more files were corrupted and are now unusable. Showing results for Search instead for Do you mean or Post new question Question Reply Topic Options Subscribe Mark Topic as New Mark Topic as Read Float this Topic to the They very rarely go bad because they have no moving parts, but if it is bad it would give these symptoms.Even if the G42 drive does not boot to Windows in click site A quick note from the author.
First you can select "Auto" from the main BIOS screen for the drive C: D: E: or F:.