Home > Error Code > Balboa Error Code Oh

Balboa Error Code Oh

Contents

If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. When I reset the breaker & turn it on then it immediately trips once again. balboawatergroup 6,670 views 4:40 Replacing Heater Straps with Heater Cables - Duration: 5:37. So before pressing any buttons, verify that water is flowing from the circ pump outlet. navigate here

Heater is deactivated. Closed Slice Valve.7. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes Turn the power back on, you have five seconds to join the wires together, do not join them before you turn the power on.

Balboa Sns Error Code

Check for Extended Pump Operation or High Ambient Temp, or contact your Dealer or Service Organization.Spa Water Cool Down• In order for the Spa Water Overheat Error Message to Automatically Reset Product Technical Support Help Me Replace A Part Product Manuals Product Color Codes Spa Panel Messages Topside Panel Manuals Common Spa Problems System Cross Reference Home>Balboa Spa Panel Messages Balboa Common Under NO circumstances should a pump be allowed to run without priming beyond the end of the 4 minute Priming Mode. If there is Now an Error Message, select Message Other than CrC or CHKSUM FAIL below.No Error Messages3.

  1. SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Hi Limit Sensor Failure.
  2. If you have a bad circuit board, you'll know it.
  3. You can often determine the make of the control system by looking inside the spa's equipment area.
  4. What causes a Spa to Overheat?
  5. Dirty Filter.5.
  6. Oh Error On Balboa System Theme Default (Default) Copy of Default Contact Us PoolSpaForum.com Community Software by Invision Power Services, Inc. × Existing user?
  7. If tripping continues, call for service.• Deactivate spa lock Hercules Control Systems for Spas or Hot Tubs: OH = Spa temp exceeds acceptable limits FLO = Flow problem ICE = Freeze
  8. Replace the board.

Switch closed while pump is deactivated. Too Many Closed Jets.6. Check water level in spa. Balboa Vs500 Error Codes Is there a sensor located there & how in the blue blazes do I change it out.???

You had a bad board. Balboa Error Codes Hot Tubs It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. Why does the panel display "FLO" alternating with current temperature? Heat Related Pump Not Running.8.

Do not use spa when temperature is flashing or the OH message is displayed. Balboa Fault Codes If it flashes OH even with new sensors, save yourself alot of heartache and trouble and just get another B2DG, or B2DG40 board. It heated for around 10 hours nearly getting up to full temp before cutting out and displaying OH again! Share this post Link to post Share on other sites christiffa25 0 Junior Member Members 0 38 posts Posted May 24, 2012 · Report post Thanks for reply "count" Apologies

Balboa Error Codes Hot Tubs

Alvin Shepherd 6,840 views 7:57 How to repair hot tub error code SN3 - Duration: 17:46. th3/39 = On startup indicates water temperature less than 39° F. Balboa Sns Error Code Low speed pump (and air blower if so equipped) will activate to assist in lowering temperature.--- = "Watchdog". Balboa Spa Error Codes The following is a list of most probable causes of this message.

Sign in here. http://onlinetvsoftware.net/error-code/005-122-error-code.php Spa unusable. I do hear a relay or something click as the OH starts flashing? Heat Related Pump Not Primed. Balboa Vs501z Error Codes

Recalibrate the pressure switch. I have pics posted on photobucket, please see my previous posts for the link. Reply With Quote 11-16-2011,09:55 PM #6 09lancer View Profile View Forum Posts View Articles Join Date Jun 2010 Posts 11 Re: OH error code Sorry for the late post. his comment is here I'm in the uk.

The Water Temperature is Always maintained within 1°F (.5°C) of Set Temperature. Balboa Hot Tub Heater Troubleshooting Press "Mode" Button to Clear Message. See if you get the same error code.

Why does the control panel display "OH"?

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. See M7 Sensors here. Wait a few seconds... Balboa Hot Tub Codes To read the Current Water Temperature, either Change to Standard Heating Mode or turn On the Heating Related Pump, and wait at least 2 Minutes.

Loading... Why does the GFCI trip immediately upon power up? Make sure that they are open. weblink HLoH = Hi Limit Over Heat.

If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below. If you have a bad thermistor, you'll know it. OHS = Overheat. If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.

I tried posting pictures but they are too large so I am trying photobucket. We suggest you check back here often, as we will be regularly updating this info. After the Problem has been Resolved, you Must Press Any Button to Reset and Restart Heater Start Up. Entire system is disabled.

Disconnect the pressure switch wire from the circuit board. The Spa or Hot Tub Panel Displays: HL, HFL - This indicates that a substantial difference in temperature between sensors has been detected during heating. - This could indicate a flow Balboa start up codes then OH starts flashing immediately before any pumps/jets have even had chance to come on. Contact your Dealer or Service Organization.

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different.