Home > Error Code > Balboa Error Code Sl

Balboa Error Code Sl

Contents

If alternating with spa temperature, it may just be a temporary condition. If flashing by itself, spa is shut down. 'SnA' Sensor 'A' malfunction 'SnB' Sensor 'B' malfunction Blocked Suction Fitting.3. In this case, if the extreme conditions are determined, the spa will display the StU message until the spa is shut down It will also set the HOt flag (HOt does Not only did you answer my questions, you even took it a step further with replying with more pertinent information I needed to know. this contact form

Status of the heater element is unknown. Do not enter the spa. Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. The following is a list of most probable causes of this message.

Balboa Spa Sl Code

This is an Operational Message, Not an Error Indication. COL = Cool condition. If display shows only this message (blinking) spa is shut down. I will tell you that...the things you have to go through to be an Expert are quite rigorous.

  • If there is No Error Message, Select "No Error Message" Below.
  • Remove the spa cover and allow the water to cool.
  • Hope this helps you out.
  • No action is necessary.PnL = Communication between the panel and circuit board is faulty.---- = "Watchdog" (spa is deactivated) A problem has been detected.Sn1 = Open sensor (heater is deactivated) or
  • All rights reserved.
  • Power on the spa must be cycled before the heater will function again.

Status of the heater element is unknown. Note: The control system brand name is usually different from the hot tub brand name. Clean and Condition Wood per Manufacturers Instructions. Balboa Hot Tub Turn Off Economy Mode If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below.

If a continuously running low-speed-only pump is only used for filtering (not for heating), that is not called a circ pump, but instead may be referred to as a "continuous filtration Balboa Sns Error Code Entire system is disabled. Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = SE = Spa operating in Standard-in-Economy Mode.

Odds are a small water leak got this started. Balboa Spa Control Manual Error & LCD Window Message Codes: ACC (Applied Computer Controls) CoLd = Temperature in the spa heater housing is below 40° F. Spa has shut down. Heater is deactivated.

Balboa Sns Error Code

Ask an Expert Online. Heat Related Pump Not Primed. Balboa Spa Sl Code Generated Sat, 01 Oct 2016 23:33:49 GMT by s_hv1000 (squid/3.5.20) Balboa Error Codes Hot Tubs drops.hot = Overheating, water over 112° F.

Robin Elkton, Maryland Meet The Experts: poolguy810 owner - pool and spa service company Satisfied Customers: 1670 Servicing pools and all brands of spas for over 28 years. < http://onlinetvsoftware.net/error-code/005-122-error-code.php depending on the model, some have a mode button which you press and release and then immediately press the temp up or down, to select SL for sleep (no heat), ST Too Many Closed Jets.6. http://hottub.synthasite.com Dec 05, 2009 | Jacuzzi Balboa R574 System for 1 2 Speed... 1 Answer I have a jacuzzi magnum 1.5 HP pump. Balboa Spa Error Codes

Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.Note: On some Early VS and GS Systems (prior to Version 23) equipped with a "Mode" Back to Top OHS, OH, or SPA TEMP LMT Message There is an "Over Heated Spa" (OHS or OH) Water Condition.One of the Water Temp Sensors has detected 110°F (43.3°C) Incoming SEoP = Sensor open or disconnected. navigate here The GFCI can also be tripped manually via the Edit Menu interface titled gFC.Button press instructions for initiating a GFCI trip manually can be found HERE.If the spa is not installed

Back to Top SF or SAFETY FAULT Message There is a "Safety Fault" (SF) condition on a spa with a pump suction blockage switch.On a spa with a pump suction blockage Balboa Hot Tub Troubleshooting OH = Over heat. FL = Flow.

If you have a Circ Pump, do this first (EL version):- Push the Jets 1 button once.

All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 365 Days, but some Spa Brands or Models may be Different. If you haven't successfully primed both pumps by the time the Priming Mode display ( Pr or PRIMING MODE depending on panel) ends, turn off the spa IMMEDIATELY.If after two minutes If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Balboa Hot Tub Codes F8 If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization.

Add Sanitizer according to Manufacturers Instructions.Note: If you do Not have an ORP Sensor installed in the Spa System, you should Never get this Message. Heater is deactivated. Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. his comment is here Jimmy Bagley, IA Wonderful service, prompt, efficient, and accurate.

The Current Water Temperature is "Unknown" (- - - or - -) while in Economy or Sleep Mode. Edit Close Save changes Attachments: Added items Uploading: 0% my-video-file.mp4 Complete. There is Not Enough Water Flow through the Heater to carry the Heat Away from the Heating Element. CTI Spa Side Error Codes th1/39 = On startup indicates temperature probe problem.

On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States Do not enter the spa. Blocked Suction Fitting.3. Press "Mode" Button to Clear Message.

Mary C. If there is Now an Error Message, select Message Other than PSt or Persist Fail below.No Error Messages3.