Home > Error Codes > Backplane Com Error

Backplane Com Error

Contents

The show diagnostic sanity Command The show diagnostic sanity command runs a set of predetermined checks on the configuration, along with a combination of certain system states. Issue the more bootflash:filename command in order to display the crashinfo file. Even though SPAN is done in hardware, there is a performance impact since now the switch carries twice as much traffic. SFP Part Number: FTLF8524P2BNV SFP Serial Number: PQR1V3L SFP Capabilities: 1, 2 or 4 Gbit Link Data Rate: 4 Gbit Switch Port: IBM_2498_B24:3 I/O base 0x0000000000002000, size 0x100 memory mapped I/O

Please verify that this is the best value from a security point of view. See Problem determination tips. Sun Aug 17 21:58:13 GMT [N6220-SAS:fmmb.instStat.change:info]: no mailbox instance on partner side. Share the ETC love!

1756-cnb Error Codes

TestTrap : . 7 . At times, error counters are incremented incorrectly because of a software bug or a hardware limitation. Common Reasons/Solutions Console in to the standby Supervisor Engine in order to determine if it is in ROMmon mode or in continuous reboot. Reply 0 Kudos « Previous 1 2 Next » « Message Listing « Previous Topic Next Topic » MORE IN COMMUNITY Learn How to Get Started Community Help Community Code of

  • In order to troubleshoot, remove all the modules except the Supervisor Engine from the chassis.
  • If the status is power-bad, the switch is able to see a card, but unable to allocate power.
  • Unset the CONFIG_FILE variable from the MSFC ROMmon.
  • The standby Supervisor Engine fails to negotiate with the active Supervisor Engine.
  • In order to identify if the standby Supervisor Engine is faulty, issue the redundancy reload peer command from the active Supervisor Engine.
  • This is example output: Note:The actual output can vary, based on the software version.
  • Re-download the Cisco IOS Software image from the TFTP server.
  • Note:If you run the Cisco IOS Software Release 12.1(8) train, the diagnostics are not fully supported.
  • If there is no disk drive error log error log, replace the affected backplane.

Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... Are you looking for the solution to your computer problem? rommon 2 >nvram_erase !--- Press Enter or Return. !--- Be sure to enter these parameters exactly: !--- The first line is a "be" (no space) followed by six zeros ("000000"). !--- Controlnet Troubleshooting Guide If there are no alarms, the output is similar to this: cat6knative#show environment alarm environmental alarms: no alarms However, if there is an alarm, the output is similar to this: cat6knative#show

Stay logged in Sign up now! Sun Aug 17 21:49:10 GMT [N6220-SAS:ses.multipath.ReqError:CRITICAL]: SAS-Shelf24 detected without a multipath configuration. Sun Aug 17 05:39:58 GMT [N6220-SAS:raid.rg.scrub.summary.cksum:notice]: Scrub found 0 checksum errors in /aggr0/plex0/rg1. In both cases, it is recommended to have a backup of the NVRAM contents.

Important: Some cluster solutions require specific code levels or coordinated code updates. Code 16#0304 Reseat the module in order to resolve the problem. This can be caused by these reasons: Busy Supervisor Engine Spanning tree protocol loop ACLs and QoS policers have throttled or dropped traffic over the inband communications channel Port ASIC synchronization cat6knative(config)#diagnostic bootup level complete !--- This command enables complete diagnostics.

Controlnet Error Codes

Reseat the backplane signal cable and repeat steps 2 through 4. Multiple hard disk drives are offline. 1756-cnb Error Codes cat6knative#show environment status backplane: operating clock count: 2 operating VTT count: 3 fan-tray 1: fan-tray 1 fan-fail: OK VTT 1: VTT 1 OK: OK VTT 1 outlet temperature: 35C VTT 2: 1756-cnb/e Error Codes The TestErrorCounterMonitor is a non-disruptive health-monitoring background process that periodically polls the error counters and interrupt counters of each line card or supervisor module in the system. %CONST_DIAG-4-ERROR_COUNTER_DATA: ID:[dec] IN:[dec] PO:[dec]

Sun Aug 17 10:00:04 GMT [N6220-SAS:cf.ic.hourlyBackplaneLinkDownTime:error]: Backplane Interconnect link has been down for 3341 minutes Sun Aug 17 11:00:00 GMT [N6220-SAS:kern.uptime.filer:info]: 11:00am up 2 days, 8:40 0 NFS ops, 196 CIFS The value for Community-Access on read-write-all operations for SNMP is the same as default. End with CNTL/Z. TestMatch : . 8 . 1756 Cnb User Manual

If there is no visual damage, try the module in another slot or a different chassis. Troubleshoot to eliminate the possibility of a faulty module. TestL3VlanMet : . 14. Sun Aug 17 06:00:04 GMT [N6220-SAS:cf.ic.hourlyBackplaneLinkDownTime:error]: Backplane Interconnect link has been down for 3101 minutes Sun Aug 17 06:44:41 GMT [N6220-SAS:raid.rg.scrub.done:notice]: /aggr0/plex0/rg0: scrub completed in 5:44:36.00 Sun Aug 17 06:44:41 GMT

If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. Code 16#0204 Connection Request Error Offlining the adapter. Inline power ports—An inline-power port is in any of these states: denied faulty other off Modules—A module is in any state other than "ok".

Sun Aug 17 21:50:58 GMT [N6220-SAS:fci.link.error:error]: Could not recover link on Fibre Channel adapter 0c after 30 seconds.

If the LED is lit, remove the drive from the bay, wait 45 seconds, and reinsert the drive, making sure that the drive assembly connects to the hard disk drive backplane. Backplane chip replace? The system appears to crash. 1756-cn2 In order to resolve this, set the diagnostic boot up level to "complete", and then firmly reseat module 4 in the chassis.

Reply 0 Kudos Options Bookmark Highlight Print Email to a Friend Report Inappropriate Content aborzenkov Re: FAS3220 Dual Chassis HA interconnect error ‎2014-08-18 12:10 AM Please boot into maintenance mode and Forward Error Correction on Backplane Serdes Links The operating margin of the longer backplane traces in the Brocade MLXe series 16Ke and 32Ke chassis may be reduced due to signal attenuation. Refer to Catalyst 6500 Series Switch Module Installation Note for more information. Style Default Style Contact Us Help Home Top RSS Terms and Rules Copyright © TechGuy, Inc.

You also get error messages that are similar to these: Router#write memory startup-config file open failed (Not enough space) Router#dir nvram: Directory of nvram:/ %Error calling getdents for nvram:/ (Unknown error