Home > Error Codes > Balboa Controls Error Codes

Balboa Controls Error Codes

Contents

Card are req.) French German Italian Spanish40634-99.pdf 40634-99.pdf 40634-99.pdf 40634-99.pdf40634-80.pdf 40634-80.pdf 40634-80.pdf 40634-80.pdf ________________________________________________________________________________________________________________________________________ ML200 Measurements: W=4.3" (10.92cm) , H=1.6" (4.06cm) User Guide 40571-99 & Ref. HLoH = Hi Limit Over Heat. If they're not, or you're not sure that both are (because you can't tell whether you have two separate flows at different rates or just one flow), momentarily turn both pumps This could indicate a flow problem. 'IC' "Ice" Potential freeze condition has been detected 'ICE' Auxiliary sensor detects potential freeze condition 'ICE' Potential freeze condition has been detected this contact form

Working... HOT = Circuit Board temperature has exceeded acceptable limit. F2 = 4 hours daily filtration F4 = 8 hours daily filtration F6 = 12 hours daily filtration FC = continuous filtration EasyPak C = Celsius CL = Current Time of Low speed pump and heater will activate until spa reaches 65ºF.

Balboa Spa Control Error Codes

Check for Water Level, Flow Restrictions, Closed Valves, Air Bubbles, and Pump Prime, or contact your Dealer or Service Organization.Check for All of the following Conditions:1. HLoH = Hi Limit Over Heat. About Press Copyright Creators Advertise Developers +YouTube Terms Privacy Policy & Safety Send feedback Try something new! Contact your Dealer or Service Organization.

Too Many Closed Jets.6. Press "Mode" Button to Clear Message. If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. Balboa Controls Manual Press "Mode" Button to Clear Message.

balboawatergroup 4,701 views 4:18 10 Most Common Hot Tub Problems - Duration: 3:12. Balboa Vs501z Error Codes The Water Temperature will probably drop Below Set Temperature between Filter Cycles. Add pH Decreaser according to Manufacturers Instructions.Note: If you do Not have a pH Sensor installed in the Spa System, you should Never get this Message. Card 40947_D FrenchRef.

Pictured here is a Balboa® control system used in Belize Spas brand. Balboa Controls Troubleshooting Note: The control system brand name is usually different from the hot tub brand name. Too Many Closed Jets.6. The low speed pump or circ pump will operate continuously until the temperature rises above 45° F.

Balboa Vs501z Error Codes

Closed Slice Valve.7. If you do not see water flowing from the circ pump outlet, IMMEDIATELY turn off power to the spa (as an attempt at heating will occur within a minute of the Balboa Spa Control Error Codes Press any "Cool", "Warm", or "Temp" Button to Exit Priming Mode.3. Balboa Vs500 Error Codes All Automatic Functions Remain OFF during this time.

Card 40947Ref. http://onlinetvsoftware.net/error-codes/bd2-sql-error-codes.php If there is Now a Message Other than a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, that Message will Now have to be Diagnosed. ICE = Freeze protection. Low Water Level.2. Balboa Hot Tub Error Codes

  • Have you taked the filter out and reset the spa to see if went away....
  • ICE = Freeze condition. 55ºF detected.
  • balboawatergroup 13,018 views 4:54 How to repair hot tub error code SN3 - Duration: 17:46.
  • Low Water Level.2.
  • Card 40281 (Mach 2.0) French German Italian Spanish40570-99.pdf 40570-99.pdf 40570-99.pdf 40570-99.pdf40570-80.pdf 40570-80.pdf 40570-80.pdf 40570-80.pdf40281.pdf 40281.pdf 40281.pdf 40281.pdf ________________________________________________________________________________________________________________________________________ ML260 Measurements: W=7" (17.78cm) , H=2.1" (5.33cm) User Guide 40633-99 & Ref.
  • Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F.
  • Press "Mode" Button to Clear Message.
  • Sn3 = Open or shorted sensor ( heater disabled).

Snb = Spa is shut down. No action is necessary. The Heater will Only operate and Heat up to Set Temperature during the Filter Cycles. http://onlinetvsoftware.net/error-codes/beep-codes-and-error-codes.php Spa unusable.

You can often determine the make of the control system by looking inside the spa's equipment area. Balboa Fault Codes Press "Mode" Button to Clear Message. Back to Top SAH or SANITIZER HIGH Message At the ORP Sensor, the "Sanitizer Level is High" (SAH).With an ORP Sensor Installed in the System, the Sanitizer Level is Above 830

FL1 = Water flow problem, inhibited or pressure switch malfunction.

per Manufacturers Instructions. Switch closed while pump is deactivated. OH = Overheating, water over 112° F. Balboa Spa Error Codes Close Yeah, keep it Undo Close This video is unavailable.

The Current Water Temperature is "Unknown" (- - - or - -) while in Economy or Sleep Mode. The idea is that, if anything in the file changes, the checksum will change and Result in a CrC Error.At Power-Up, the System has Failed the Program Checksum Test. If alternating with temp, may be temporary condition. http://onlinetvsoftware.net/error-codes/bd2-error-codes.php If Not, Continue to Next Step.Spas with Pump Suction Blockage Switch:1.

Low Water Level.2. th2/current temperature = On startup indicates temperature probe problem. It also said that it would be displayed three times then shut the spa down. Heat Related Pump Not Running.8.

For more information regarding Balboa tech support click here Gecko Spa Side Error Codes FLO : Pressure switch failure, switch open FLC : Pressure switch failure, switch closed Prr : Temp If there is Now a "PSt" or "PERSIST FAIL" Persistent Memory Error Message, contact your Dealer or Service Organization. Error codes are for quick reference only,please contact manufactures for additional information. Card 40633-80 (Mach 3.0: BOTH User Guide & Ref.

Sign in to add this to Watch Later Add to Loading playlists... Closed Slice Valve.7. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. Closed Slice Valve.7.

Back to Top ICE, IC, or FREEZE COND Message A Potential Freeze Condition has been Detected, and "Ice" (ICE) in the System is being Prevented.44°F (6.7°C) or Lower has been Detected