Home > Error Codes > Balboa Pack Error Codes

Balboa Pack Error Codes

Contents

Hi limit sensor is disconnected or shorted or the spa temperature is above 112° F. balboawatergroup 3,050 views 5:49 Balboa Legacy Systems Series - Troubleshooting Topside Panels and System Outputs - Duration: 6:37. Watch Queue Queue __count__/__total__ Find out whyClose Balboa Legacy Systems Series - Troubleshooting Panel Messages Sn1, Sn3, Sn or Heat Status LED balboawatergroup SubscribeSubscribedUnsubscribe428428 Loading... If the "SF" Error Message is not cleared from the topside panel display, contact your Dealer or Service Organization. this contact form

I CE2 = Freeze protection. Drain and Refill the Spa Water per Manufacturers Instructions. You can often determine the make of the control system by looking inside the spa's equipment area. ehowathomechannel 233,067 views 2:42 Loading more suggestions...

Balboa Spa Error Codes

I have no experience with troubleshooting or fixing spas. Spa unusable. Pump may also be deactivated). Error codes are for quick reference only,please contact manufactures for additional information.

  • Sign in to make your opinion count.
  • If the Spa with the "SF" Safety Fault Error Message has a pump suction blockage switch, Select "Spas with Pump Suction Blockage Switch" Below.
  • If the SLP or SL Message is ON Solid (Not Flashing) on the Display, the Spa is Operating in the Sleep Heating Mode, but there is No current water temperature because
  • Heater disabled but the spa is operational.
  • If display shows only this message (blinking) spa is shut down.
  • If there is Now a Message Other than a "CrC" or "CHKSUM FAIL" Error Message, that Message will Now have to be Diagnosed.
  • Working...
  • HL = High limit switch tripped.
  • Home Pool School Forum FAQ Forum Actions Mark Forums Read Quick Links View Site Leaders PoolMath Rules What's New?
  • With the Heat Related Pump Running, wait at Least 2 Minutes for the Correct Actual Water Temperature to be Displayed.

Email Address: Password: You will be prompted to enter your password on the next page Create an account Forgot Password? Calcs & Charts Pool Gallon Calc Liquid Calc pH Chart Deck-O-Seal Gladon Chart Salt Levels Sand Qty / Filter Stabilizer Levels Education & Safety Terminology Training/Seminars Heater Elements Thrubolt Motors Transformer If a given pump has two speeds, press its Jets button a second time to set it to high speed. (High speed should be used for priming.)- When you have verified Balboa Hot Tub Error Codes Back to Top PHL or PH IS LOW RAISE PH Message At the pH Sensor, the "pH Level is Low" (PHL).With a pH Sensor Installed in the System, the pH Level

The GFCI can also be tripped manually via the Edit Menu interface titled gFC.Button press instructions for initiating a GFCI trip manually can be found HERE.If the spa is not installed Since it was so cold, and my spa was in sleep mode, I opened the panel and made sure there was water ( not ice) in the heating element. (I cracked The "SnS", "Sn", or "SENSOR SYNC" Fault has occurred for more than 1 hour, indicating one or both Sensors are several degrees off, and Spa Functions are Disabled. In this condition, an attempt is made to trip the GFCI, which would shut off all power to the spa.

Sign in 2 0 Don't like this video? Balboa Fault Codes This Mode allows the User to Replace or Clean a Pressure Side Filter Cartridge without Equipment turning ON unexpectedly. HLoH = Hi Limit Over Heat. Contact your Dealer or Service Organization.A Sensor Failure Message may indicate Excessively High Heater Temperatures which can Scald or Burn!If the Heater is Not Cool Enough to Safely Service, allow the

Balboa Vs501z Error Codes

Dirty Filter.5. Hold = Panel sensors have been pressed too many times in a short period of time. Balboa Spa Error Codes Aquarium PartsBath PartsPool PartsSpa PartsWhite GoodsClearance Items (Bath/Spa) Dealer/Tech ApplicationWarranty InformationProduct ReturnsBack Ordered ProductsDownloads SectionQuestions? Balboa Vs500 Error Codes Blocked Skimmer.4.

Too Many Closed Jets.6. http://onlinetvsoftware.net/error-codes/bgp-error-codes.php Remove, Clean, and Reinstall Spa Filter Cartridge per Manufacturers Instructions. Blocked Skimmer.4. Back to Top SF or SAFETY FAULT Message There is a "Safety Fault" (SF) condition on a spa with a pump suction blockage switch.On a spa with a pump suction blockage Balboa Spa Control Error Codes

FLO2 = Closed or shorted flow switch on system startup Pinnacle OH = Temperature has exceeded 110° F SN = Sensor failure FL = Flow/pressure switch stuck in closed position Spa It may be possible for a stuck relay to free itself after the power cycle, but the spa cannot clear the the HOt message without starting up in Test Mode first. This is normal and is not an indication of an error. 'pd' Power supply, unit running on battery backup slow-dissolving 'SA' Spa is shut down. http://onlinetvsoftware.net/error-codes/beep-codes-and-error-codes.php Heater is deactivated.

This is NOT intended as a service guide or a means for you, as the consumer, to service your equipment in any way. Balboa Trouble Codes Then press Temp once to exit Priming Mode. All Reminder Messages can be Disabled through the Topside Panel Users Menu.* Note: The Balboa Default Interval is 90 Days, but some Spa Brands or Models may be Different.

Wait 4 Minutes or Press any Temp Related Button to Exit Priming Mode to Normal Operation.Note: On some Early VS and GS Systems (prior to Version 23) equipped with a "Mode"

Safety should ALWAYS be your first consideration! Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F. The Sensors are Possibly Out of Sync with Each Other, or Not Indicating Close to the Same Temperature at Both Sensors. Balboa Spa Control Manual This is Not an Error Message.

Hold = Panel sensors have been pressed too many times in a short period of time. Back to Top Pr or PRIMING MODE TAKES 4 MIN Message The Spa is Operating in "Priming" (Pr) Mode.The Spa has just been powered up and is in Priming Mode for FLO2 = Closed or shorted flow switch on system startup Dream Maker Spa Side Error Codes OH = Overheat 108° F, spa is deactivated. http://onlinetvsoftware.net/error-codes/bd2-sql-error-codes.php The sensor that is plugged into the sensor "A" jack is not working 'Sb' Spa is shut down.

Press "Mode" Button to Clear Message. Turn OFF the Power to the System and Turn it back ON again to put System into Priming Mode.2. dr = Inadequate water detected in heater. If water is flowing from the circ pump outlet, proceed to test all the other pumps.If the Circ Pump is primed, or if you Do Not have a Circ Pump, then:-

Spa is shut down. This indicates a Possible Problem with the System Board. Contact qualified service technician. COOL = Spa water is more than 20° F cooler than the temperature set point.

On the subsequent power-ups, the GFCI test is skipped because the proper flag has been set in the software.Note: The GFCI Test Feature should only be Enabled in the United States Too Many Closed Jets.6.