Home > Error Codes > Bcr Control Initialize Error

Bcr Control Initialize Error

Contents

Was the information on this page helpful? Next "clean up" I will do just that. Please try the request again. View library and drive error logs. check over here

If there is a tape in a drive, replace the magazines and run the Force Tape Eject operation. B0 Command from Library controller to robotics controller did not complete in time allotted Reset the device and retry the operation. Ensure that nothing is stacked on top of the device because any weight on top of the device can bow the top cover down and interfere with the robotics. is 13:00.

He Cannot Initialize Barcode Reader Code 80 01

BLYNK_WRITE(3) { int i = param.asInt(); if (i == 1) { digitalWrite(RELAY1, HIGH); digitalWrite(RELAY2, LOW); } else { digitalWrite(RELAY2, HIGH); digitalWrite(RELAY1, LOW); } } Any ideas what I am doing wrong? If the error persists, contact support personnel, visit www.hp.com/support . F0 Drive exceeded temperature specification Check ambient temperature to ensure that it is within operating specifications.

The text after the main error code (Robotic controller generic problem in this example) is the text description for the error code. See the Force ejecting a drive (Support > Force Drive Eject) section in Operator Control Panel (OCP) . sub-code 00: drive sled #1, sub-code 01: drive sled #2 NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive. He Sled Position Not Found Code 9b 37 Click the Health button on the main toolbar to generate and display a standard report or click the Support button on the main toolbar to display the Support screen for additional

Check that the network configuration is correct. Msl4048 Error Codes The event ID is the number on the header line, 0x006E in this example. Elevator is the part of the robotics assembly that moves in the vertical direction. hackmanj 2016-01-11 00:08:29 UTC #7 Thank you, it must hurt your eyes to look at my code.

If an error occurs during operation, the device stops the current operation and displays an error code on the LCD screen. He Elevator Blocked Code 8b 26 If power-cycling does not resolve the issue, contact HP support. A1 Open Mail Slot failed Retry the operation If not successful, contact technical support B0 Command from library controller to robotics controller didn’t complete in time allotted Reset the unit Retry The text description in the header (robotic controller error in this example) is the simple text description of the main error code.

Msl4048 Error Codes

BLYNK_WRITE(3) { int i = param.asInt(); if (i == 1) { digitalWrite(RELAY1, HIGH); digitalWrite(RELAY2, LOW); } else { digitalWrite(RELAY2, HIGH); digitalWrite(RELAY1, LOW); } } void loop() { Blynk.run(); timer.run(); } Dmitriy Run the Wellness Test 8A Slider obstructed NOTE: Slider is the part of the robotics assembly that plunges in and out for get and put operations. 8B Elevator obstructed NOTE: Elevator He Cannot Initialize Barcode Reader Code 80 01 Second code - The main error code (89 in this example). He Elevator Blocked Error During Move Elevator To Scan Position Code 8b 26 A0 Sled range of motion out of specification NOTE: Sled is the part of the robotics assembly that moves the robot towards the OCP or back towards the drive.

B1 Robot controller reported format error on command from Library controller Reset the device and retry the operation. Once I get the command structure down I can build out everything I need however I keep hitting a wall when I follow examples I've find elsewhere on this community for Verify that nothing is obstructing the robot. 8B Elevator obstructed Run the wellness test 8C Rotation obstructed Run the wellness test. I usually put it above loop() function, not in setup, not in loop, just as standalone function. -edit Too late, lol Home Categories FAQ/Guidelines Terms of Service Privacy Policy Powered by He Slider Blocked Error During Second Slider Movement Code 8a 63

Also access error information from the Support sub-menu item, see Viewing logs (Support > View Logs) . Ensure that there is nothing obstructing the gripper. I am using SimpleTimers. // Managing "Modes" For Xbox, etc. NOTE: The support ticket downloaded from the RMI will only contain information about the Library.

To download a support ticket from the device, do one of the following: From the RMI Support > Support ticket screen, click Download. Msl2024 Error Codes For example: 1:00 p.m. The log shows the Date/Time, Code and Description.

The message shows the error code and a description of the error.

Power cycle the device and try again. Main error codes Error code Description Details and solution 80 Cannot initialize bar code reader Power-cycle the unit and retry the operation. 81 No response from bar code reader 82 No Figure 3: Critical event details The time stamp is in the format hours : minutes : seconds. Mechanical Block Code 8d 07 Ibm The main error code (0x83) is displayed in parenthesis as the Global error code.

Either void setup() { ... } either void setup() { ... } hackmanj 2016-01-11 00:07:19 UTC #6 You make it look easy, thanks very much, I moved it between setup and Fourth code - Sub-code-specific information for factory use only Figure 1: Support: Library logs page top Finding error code information on an L&TT support ticket or report An L&TT support ticket The device must be supported under both of its side edges or the bottom can bow and impede robotic movement. The hours are in 24-hour clock format.

DD Warning event. If the device was moved or shipped with tape cartridges in the magazines, verify that the cartridges did not come out of the magazines to obstruct the drive. The wellness test exercises all robotic movements and checks the status of the electrical components and communication. Ensure that nothing is obstructing the opening of the mailslot.

top Error sub-code descriptions Robotic error sub-codes The table below (Robotic error sub-codes) lists the robotic error sub-codes. Was the information on this page helpful? Check all fans to determine whether they are working properly. Insert a USB flash drive into the USB port on the rear panel and then from the OCP, select Download support ticket to USB.

B4 “Tape in gripper” sensor did not report the expected value Remove the magazines and inspect them for a stuck tape. D0 ROM checksum incorrect Retry Library firmware upgrade. If the failure remains with the same slot, the magazine may be at fault. Remove and inspect the magazine or drive for a stuck tape Run the Wellness Test B5 Robotic controller not responding to command from library controller Reset the unit Retry the operation

The message shows the error code and a description of the error. It uniquely maps to an error code. top Link for troubleshooting Click here to view information on Troubleshooting . Thank you!

Contact technical support. Start of content Hewlett Packard Enterprise Support Center Product SupportSearch HPE Support CenterDownload optionsDrivers & softwarePatch managementSoftware updates & licensingDiagnostic passwordsTop issues & solutionsTop issuesMost viewed solutionsTroubleshoot a problemAdvisories, bulletins & Expand the event for more information (as shown in Figure 3). Dmitriy 2016-01-11 00:05:12 UTC #4 BLYNK_WRITE should be outside any method.

The code after LIB/ERR (80 in the example) will be 80 or 40. 80 indicates a hard error, 40 indicates a soft error. Update the Library to the latest version.